







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Asphalt Driveways & Resurfacing in Providence Village, TX: What It Costs and How It Works
Asphalt driveways & resurfacing in Providence Village, TX typically run $3,500 to $9,000 for a full new asphalt driveway, and a resurfacing (overlay) on an existing base usually lands in the lower half of that range depending on square footage and base condition. Most driveways here can be torn out, re-graded and paved in two to three working days, with a fresh seal coat applied after the asphalt cures. Call (844) 560-4467 for a free on-site estimate and a written, line-item quote before anything gets torn up.
The process, step by step, so you know what day one actually looks like

Asphalt is not a one-visit job, and the honest sequence matters because you’ll be without your driveway for a stretch. Here’s how we run it in Providence Village.
Stage 1: Site walk and layout (about 45 minutes)
We measure the existing driveway, check the slope away from the slab, and note where the clay soil has already started to move. You decide the finished width and whether you’re adding a turnaround or widening to fit two vehicles. This is also where we flag whether the HOA’s architectural review committee needs a submittal, because in Providence Village exterior changes often need approval before a permit is even pulled.
Stage 2: Tear-out and base prep (day one)
Broken asphalt and any failed concrete apron come out. We then re-grade and compact the base in lifts, which is the single biggest predictor of how long the new surface lasts. On Blackland Prairie clay, that base work is where a cheap driveway starts to fail – skip it and you’ll see cracking within a couple of seasons. We inspect drainage and confirm water still sheds toward the street and away from the foundation.
Stage 3: Paving (day two, or late day one on smaller jobs)
Hot-mix asphalt goes down at the thickness your use calls for (2 inches compacted is standard for residential; heavier if you park a truck or trailer). It’s rolled while hot and the edges are tamped. You’ll want to stay off it for 24 to 48 hours, and keep heavy loads off for a week.
Stage 4: Cure and seal (roughly 6 to 12 months later)
New asphalt needs to cure before it’s sealed, so a seal coat is a separate visit down the road, not a same-week add-on. Sealing too early traps oils and creates a soft surface. This is a decision point you should calendar, not rush.
Stage 5: Final walk-through
We walk the finished edge, drainage and transitions with you and put the workmanship guarantee in writing. Every job is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll choose between
Asphalt isn’t one product. What you pick changes cost, lifespan and how the driveway handles a North Texas summer.
- Standard hot-mix asphalt (2″ compacted): The residential standard and what our $3,500 – $9,000 range is built around. Smooth, quiet, and the least expensive per square foot. The trade-off is that it’s the most sensitive to a poor base and to summer heat.
- Heavier-thickness asphalt (3″): Costs more but holds up better under trucks, trailers and heavy equipment. Worth it if you routinely park something loaded.
- Overlay / resurfacing: Paving a new layer over a sound existing base. Cheaper than full tear-out and faster, but only works if the base underneath is still solid – if it’s cracked through, an overlay just transfers the cracks up.
- Asphalt with a paver border: A concrete or Belgard or Techo-Bloc paver edge gives a sharper finish and defines the driveway line, which some Providence Village HOAs like for curb appeal. Adds cost but reads clean against brick veneer.
- Seal coat schedule: A quality seal every 2 to 3 years protects against UV and moisture. It’s maintenance, not a fix, and skipping it ages the surface faster than most homeowners expect.
What Asphalt Driveways & Resurfacing costs in Providence Village, TX

Expect $3,500 to $9,000 for a new asphalt driveway here, with resurfacing generally toward the low end. The number that actually lands on your quote is driven by five things.
| Line item | Typical range |
|---|---|
| New asphalt driveway paving | $3,500 – $9,000 |
| Resurfacing (overlay) | Lower end, base-dependent |
| Full driveway replacement (tear-out + new) | $5,000 – $14,000 |
| Driveway sealing (after cure) | $250 – $700 |
- Size and shape: A single-car drive is a different job than a long, curved one that eats square footage.
- Base condition: Soft spots, failed clay and old concrete apron mean more demolition and re-grading.
- Access and drainage: Tight lots, culvert changes or re-sloping for drainage push cost up.
- Thickness and mix grade: The heavier the asphalt, the higher the material cost.
- Approvals: If the HOA architectural review or a permit applies, that’s real time and sometimes paperwork cost.
A written estimate from us itemizes tear-out, base prep, asphalt tonnage and thickness, and disposal. What it won’t quietly include: unforeseen utility conflicts or a base that turns out worse than it looked once the old surface comes off. We tell you those up front, and with upfront pricing the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Providence Village homes specifically do to this job
Providence Village is a master-planned, HOA-heavy community built almost entirely after 2000 on former ranch land north of US 380. That changes this job in ways it wouldn’t in older Denton County towns. Construction here is less about fixing worn-out structures and more about working within tight architectural review rules – design-review submittals, driveway and structure color palettes, and lot-line drainage regulations that don’t exist in Sanger or Aubrey. Before we pave, we confirm what the architectural review committee needs to see, so you’re not looking at a violation notice later.
The clay soil under these production-built homes expands and contracts hard with our wet-dry cycles, so driveways commonly crack and shift. Because so many homes came from the same handful of builders in phases, identical driveways show the same failure points block after block. We account for that in the base work – it’s the difference between a driveway that lasts and one that cracks by year two.
Serving Providence Village, TX – Our Local Coverage Area
We serve Providence Village and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Asphalt Driveways & Resurfacing in Providence Village

Most driveways are torn out, prepped and paved in two to three working days, then need 24 to 48 hours off-limits before light use. Seal coating happens months later once the asphalt cures. Call (844) 560-4467 and we’ll give you a date range for your specific driveway.
Often yes on the HOA side, and sometimes a permit as well. Providence Village’s architectural review committee typically must approve exterior changes before a permit is pulled, so we build that into the schedule. Call us and we’ll walk you through what your community requires.
Resurfacing usually lands in the lower half of the $3,500 – $9,000 range, while a full replacement with tear-out runs $5,000 – $14,000. The deciding factor is whether the base underneath is still sound. Call (844) 560-4467 for an exact quote – estimates are free.
Not if the base is prepped and compacted properly. Blackland Prairie clay moves with our wet-dry cycles, so the subsurface work is what prevents repeat cracking. We re-grade and compact in lifts rather than paving over a failing base.
Every driveway is backed by our 730-Day Done Right Promise – if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in residential construction, and it’s written, not implied.
Get a free estimate for asphalt driveways & resurfacing in Providence Village
Call (844) 560-4467 for a free on-site estimate on asphalt driveways & resurfacing in Providence Village, TX. We’ll measure your driveway, check the base and drainage, confirm what the HOA review needs, and hand you a written, line-item quote with upfront pricing. If you’re planning a wider project, this often fits into a full Driveway & Pavers in Providence Village scope. Questions first? Our Driveway & Pavers service line has the full picture, and you can see everything we cover across Providence Village.
Written by the team at Groundwork Construction Co.












