







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Concrete Driveways & Concrete Work in Farmers Branch, TX: What It Takes
Concrete driveways in Farmers Branch, TX run $4,500 – $12,000 for installation, and most projects we run involve 3 to 4 working days of on-site concrete work plus a week of curing before you park on it. A full driveway replacement lands at $5,000 – $14,000. Call (844) 560-4467 for a free on-site estimate with a written line-item quote.
How a concrete driveway job actually runs, day by day

Every driveway we pour follows the same five stages, and you’ll know exactly what’s happening at each one before the crew shows up.
Stage 1: Demo and haul-off (day 1)
Existing concrete gets broken, loaded, and hauled out. On the older Farmers Branch lots, that also means cutting and tying in any utility cleanouts the city requires. You’ll confirm the driveway layout and width here, and we mark utility locates before anything gets cut.
Stage 2: Subgrade and grading (day 1 – 2)
What’s under the slab matters more than the slab in this clay soil. We excavate to the right depth, proof-roll the subgrade, and set a positive slope away from the house. This is the stage where the homeowner decides on drainage direction, and if the driveway ties into the street apron, we set the transition here too.
Stage 3: Formwork and reinforcement (day 2)
Form boards go up, then rebar or wire mesh gets tied in place with chairs to keep it off the dirt. You’ll want to walk the forms with the crew lead and confirm any expansion joint locations before the pour. If the driveway ties into a garage slab or a walkway, we cut those cold joints now.
Stage 4: The pour and finish (day 2 – 3)
Ready-mix arrives and gets placed, screeded, and floated. Finish gets decided right here: broom, salt, exposed aggregate, saw-cut control joints. This is the last chance to change the surface treatment before the concrete starts setting.
Stage 5: Curing and sealing (day 3 plus cure time)
We keep it wet-cured for a week, then apply a cure-and-seal coat. No parking on it until we give you the word, which is usually 7 – 10 days for full traffic, longer if the concrete is poured in a cold snap or the mix runs wet.
Every job we run is backstopped by our 730-Day Done Right Promise. If it’s not done right, we make it right, and that covers workmanship on the concrete itself.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll choose between
- Standard gray broom finish (about 3,200 psi to 3,500 psi): the workhorse for driveways. Good traction, holds up to Texas heat, budget-friendly. This is what most Farmers Branch homeowners pick.
- Exposed aggregate finish: the aggregate gets exposed with a chemical wash after the pour. Better grip and a bit of visual texture, and it hides tire marks better than broom finish. Expect a modest upcharge per square foot.
- Stamped or patterned concrete overlays: looks like pavers or stone at a lower cost than real pavers. Honest trade-off: the stamped joints can hold water and dirt, and overlay finishes will need re-sealing every 2 – 3 years. If you want pattern without the overlay, look at the Driveway & Pavers in Farmers Branch options instead.
- Rebar vs. wire mesh: rebar costs more but resists cracking significantly better on expansive clay. Wire mesh is cheaper and works for light-duty driveways. On old clay lots, we lean rebar.
- Fiber-reinforced mix vs. standard: fiber keeps shrinkage cracks tighter and adds about $8 – $15 per cubic yard. Worth it if the driveway is wide or the lot drains poorly.
- Full replacement vs. repair with overlaid topping: if the cracks are shallow and the subgrade is sound, a bonded overlay costs less than a full tear-out. If the slab is failing on clay movement, overlay just delays the problem.
What Concrete Driveways & Concrete Work costs in Farmers Branch, TX

Our written ranges for this city:
- Concrete driveway installation: $4,500 – $12,000
- Full driveway replacement: $5,000 – $14,000
- Driveway sealing (protects the new slab): $250 – $700
Those ranges move on four things:
- Square footage. A 2-car driveway on a standard 7,000 – 8,000 sq ft lot runs smaller than a long, curved approach. Add $5 – $8 per square foot for every extra 100 sq ft.
- Demo and haul-off. Old concrete is heavy and the dump fee is real. If the existing slab needs breaking and removal, that’s typically $1,200 – $3,000 depending on thickness and access.
- Clay subgrade correction. Expansive clay in Farmers Branch sometimes needs 6 – 12 inches of over-excavation and a stabilized base before the pour. That pushes you toward the top of the range.
- Grade and drainage work. If the driveway needs to be re-graded to keep water off the house slab or a neighboring lot, plan on an added $800 – $2,500.
- Finish and mix. Exposed aggregate or stamping adds cost over broom finish and keeps you at the higher end.
A written estimate from us covers demo, haul-off, subgrade prep, reinforcement, the concrete mix, finishing, and the cure-and-seal coat. It does not cover city permitting fees or soil stabilization from a separate engineering firm, but we’ll be clear about both before work starts. Upfront pricing, no surprises. You know the number before we break ground.
See the difference
Before
After
Before
After
Before
AfterWhat Farmers Branch homes specifically do to this job
Farmers Branch is a built-out inner-ring Dallas suburb where nearly all the new construction is infill and redevelopment. Teardowns of 1950s – 60s ranch homes get replaced with larger custom builds on the same lot, and that means we’re working in tight, fully-occupied residential blocks. Staging equipment, staging the concrete truck, and coordinating with neighbors matters more than raw lot size. Most of the stock is single-story brick ranch on a slab, with original cast-iron plumbing running under or near the drive. That plumbing matters, because when we demo an old drive, we’ve got to know where the sewer cleanout sits before the breaker goes down.
Clay soil and North Texas heat are the other two factors. Slabs swell and shrink through the wet-dry cycle, and a driveway that wasn’t properly reinforced or saw-jointed will crack at the control joints within a few years. Hail and wind storms are hard on the surface too. The interesting risk on a Farmers Branch redevelopment lot is drainage: the new two-story build next door often pushes setback and impervious-cover limits, so stormwater has to be directed somewhere specific. When we pour a new driveway on your side of the line, we grade and set the slope so water runs to the street, not onto your neighbor’s slab. If the driveway project is part of a bigger lot change, homeowners often pair this with ADU Site Prep & Utilities in Farmers Branch so utility routing and grading get planned together.
ZIP code 75234 covers the residential core. If you’re in Farmers Branch proper, the drive work you’ll need most often is with a driveway pour, a curb cut, or a replacement instead of a new-build. The city requires a permit for new driveway construction and for changes to curb cuts, and inspection happens after the base is prepped and again after forming. We pull the permit and coordinate the inspection so you don’t have to.
Serving Farmers Branch, TX – Our Local Coverage Area
We serve Farmers Branch and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Concrete Driveways & Concrete Work in Farmers Branch

Most concrete driveways here take 3 to 4 days of active work, plus a 7-to-10-day cure before you park on them. Demo and prep run days 1 and 2, the pour lands on days 2 or 3, and finishing and sealing wrap up the same day. Weather delays from rain on a fresh pour push the schedule, and we’ll flag that as it happens. Call (844) 560-4467 for an exact schedule window for your driveway.
Yes – new driveway construction and any change to a curb cut or street apron require a permit through the city. Replacement of an existing driveway on the same footprint sometimes doesn’t, but it depends on scope and tie-in details. We confirm the permit scope before we break ground, and we pull the permit and coordinate inspections.
Sometimes yes, sometimes no. A bonded overlay can go over an existing slab in good condition with only shallow surface cracking. If the concrete is breaking at the control joints due to clay movement or the base has shifted, an overlay just delays the failure. We’ll tell you honestly which category yours is in after a site visit.
No, not on our written estimate. The number we quote is the number you pay for the scope in writing. If you add square footage, change the finish, or a soil correction is needed that wasn’t visible at estimate time, we stop and quote the change before we proceed. Upfront pricing, no surprises.
Every driveway we pour is covered by the 730-Day Done Right Promise. That’s a workmanship guarantee on everything we install, and if anything we built isn’t done right, we come back and make it right. The 730-day window applies to our portion of the job. Call (844) 560-4467 and we’ll walk you through exactly what’s covered.
Get a free estimate on your Farmers Branch driveway
We’ll walk the site, measure the actual driveway footprint, check the subgrade, and give you a written line-item quote before you commit to anything. Calls are answered by a live person 24/7, and the estimate itself costs nothing. Book a visit by calling (844) 560-4467 and mention concrete driveways or a full driveway replacement. If you want to see the wider scope, our Driveway & Pavers service covers it, and if your project also involves a new entry door or garage access, Door Installation in Farmers Branch is a natural pairing.
Written by the team at Groundwork Construction Co.












