







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
What does a chain link fence in Farmers Branch, TX cost and how long does it take?
A chain link fence in Farmers Branch, TX typically runs $3,500 to $9,000 for a standard residential lot, with most properties landing between $4,200 and $6,800 depending on linear footage, height, and gate count. A straightforward 150-foot backyard enclosure is usually a one-to-two-day job once materials are on site; larger perimeters with multiple gates stretch to three or four days. Call (844) 560-4467 for a free on-site estimate with line-item pricing before you commit to anything.
How a chain link fence goes in, stage by stage

A chain link fence is not a complicated build, but the order of operations is where most subpar jobs fail. Here is exactly what happens, and where you make decisions along the way.
Stage 1: Site walk and layout (day 1, about an hour). We walk the property line with you and confirm the exact fence route, gate placement, and post spacing. This is your decision point on height (4-foot, 5-foot, or 6-foot) and gate swing direction. We also call 811 for utility locate marks, which must clear before any post goes in the ground. On older Farmers Branch lots this step matters because original cast-iron plumbing and irrigation lines are often not where you would guess.
Stage 2: Demolition and clearing (day 1, 2 to 4 hours). If there is an existing fence, it comes out: posts pulled, concrete footings broken and hauled off, old fabric rolled and removed. Overgrown brush along the line gets cleared so the new run is straight. You decide at this stage whether the old line stays or shifts, which costs roughly $8 to $14 per linear foot to change.
Stage 3: Post setting (day 1, 3 to 5 hours). Posts go in at 8-foot spacing, set in concrete, and get a string-line check for straight and plumb. Terminal, corner, and gate posts get larger footings and heavier-gauge steel because they carry the tension of the whole run. This is the one stage that cannot be rushed: concrete needs to cure before the fence goes up, which is why most projects span two visits.
Stage 4: Framing and fabric (day 2, 3 to 4 hours). Top rail, tension bands, and the chain link fabric go up, then get stretched tight with a come-along and secured. A proper stretch is what stops the sagging and rattling that cheap fences develop within a year. Gates get their frames, hinges, and latches hung and tested here.
Stage 5: Walkthrough and cleanup (day 2, under an hour). We walk the finished line with you, confirm gate operation, and clean the site. Any post needing a re-set gets flagged on the spot.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll actually choose between
Chain link is not one product. These are the spec choices that separate a fence that lasts 20 years from one that looks tired in five.
- Fabric gauge: 11.5-gauge is the standard residential pick and holds up well through North Texas wind; 12.5-gauge is thinner and cheaper but dents easier in hail; 9-gauge is heavy commercial grade, overkill for most homeowners but worth it on corners that take abuse.
- Post gauge: 16-gauge posts are standard, but 14-gauge or heavier terminal posts are the upgrade to make if you expect kids, dogs, or climbers to lean on the fence.
- Coating: Galvanized fabric is the economical pick; vinyl-coated in black or green costs roughly 15 – 25% more and looks better against landscaping while hiding rust blooms.
- Height: 4-foot is the common residential run, 5-foot adds a bit of privacy and canine security, 6-foot is the max most residents want and reads as a stronger privacy line.
- Gates: Walk gates are standard; drive gates and double gates for equipment access cost more and require heavier hardware. Decide gate count before ordering materials, because hardware choices hinge on it.
- Top rail and tension wire: Add a bottom tension wire to keep the fabric tight at ground level and stop dogs pushing through.
What chain link fence costs in Farmers Branch, TX

For a Farmers Branch residential project, expect $3,500 to $9,000. The wide band comes down to five variables that push a job toward either end.
- Linear footage. A typical quarter-acre lot needs 200 to 300 feet. The per-foot rate drops as footage climbs, but a big perimeter still costs more in total.
- Existing fence removal. Tearing out an old fence and its concrete footings adds $500 to $1,500 on most Farmers Branch jobs.
- Terrain and grade. Flat ground is easy; sloping terrain requires stepped or racked panels and adds labor.
- Gate count and size. Each additional walk gate adds a few hundred dollars; drive gates and double gates add more thanks to heavier hardware.
- Material grade. Moving from 12.5-gauge to 9-gauge fabric and heavier posts can raise the ticket 20 – 30%.
Your written estimate should list footage, gauge, post size, gate count, and a line for removal if needed, with the total up front. Watch for quotes that skip footings or leave gate hardware off the line. You’ll also want to confirm whether permit fees are included if your project needs one.
See the difference
Before
After
Before
After
Before
AfterWhat Farmers Branch homes specifically do to this chain link job
Farmers Branch is a built-out inner-ring Dallas suburb where new construction is almost entirely infill and redevelopment: teardowns of 1950s-60s ranch homes replaced with larger custom builds on the same lots. That means fence work here happens on tight, fully-occupied residential blocks in ZIP 75234, where staging, driveway access, and neighbor relations matter more than raw lot size. On streets where a two-story infill sits beside a 1960s brick ranch, you’ll often see grading that channels runoff toward the older slab, and a fence line has to respect that drainage path. Expansive clay soils swell and shrink with the wet-dry cycle, so posts set in shallow concrete will heave and shift within a few seasons; we set footings deeper on these lots to compensate.
Most of the housing stock we work on is 1950s-1970s single-story brick ranch on slab foundations with original cast-iron plumbing, and the utility locate step is where surprises show up. Where you’re building an accessory structure or running new utilities at the same time, homeowners often pair this with ADU Site Prep & Utilities in Farmers Branch so the trenching and locates happen once. And because Farmers Branch lots were platted for one-story ranches, some infill builds push setback and impervious-cover limits, so a fence that reads as a property-line marker can also trigger a grading review if it fights the drainage plan.
Serving Farmers Branch, TX – Our Local Coverage Area
We serve Farmers Branch and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – chain link fence in Farmers Branch

Most residential chain link fence projects in Farmers Branch take one to two days of on-site work, split across two visits so the post concrete can cure. A larger perimeter with multiple gates runs three to four days. Weather in North Texas can add a day if a storm lands during the build.
In most cases a standard residential chain link fence line at common heights does not require a permit, but corner lots, rear setback lines, and taller privacy runs can trigger review. We confirm the requirement for your specific address before any post goes in the ground. Call (844) 560-4467 and we’ll walk through what applies to your lot.
Linear footage and existing fence removal drive the number more than anything else, followed by gate count and material gauge. Farmers Branch projects come in between $3,500 and $9,000, with typical jobs landing around $4,200 – $6,800. Call (844) 560-4467 for an exact quote, and it comes with line-item pricing so nothing is hidden.
Every chain link fence we build is covered by the 730-Day Done Right Promise: if the workmanship is not right, we make it right. That covers post setting, fabric stretch, and gate hardware for two full years from completion. Call (844) 560-4467 to talk through warranty specifics for your project.
Yes. On tight Farmers Branch blocks, where one property line meets three neighbors, matching gate hardware and coating color is a quick way to keep the street looking uniform. We’ll measure your neighbor’s gauge and coating so the new run doesn’t clash. Call (844) 560-4467 to schedule a site visit and we can confirm the match.
Get your chain link fence priced in Farmers Branch
We give Farmers Branch homeowners a free on-site estimate with line-item pricing, footage, and material specs in writing, so you know the number before a shovel hits dirt. When you call (844) 560-4467, a live person is on the other end, and we’ll schedule a visit that fits your week. If a full perimeter is on your list alongside other work, our Fence Installation page shows the full scope, and you can see how this fits into our Fence Installation in Farmers Branch coverage. Homeowners often pair this with Door Installation in Farmers Branch while we’re on-site. We’re proud to serve the community and Farmers Branch in full.
Written by the team at Groundwork Construction Co.












