







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Door Installation in Irving, TX: What the Job Actually Involves
Door Installation in Irving, TX runs $450 to $2,400 for a single exterior door, all-in, with impact-rated and wind-load-rated entry systems pushing toward the top of that band. A standard pre-hung swap takes one day. A new opening cut into a brick-veneer wall takes three. The difference is framing, flashing, and the inspection that follows. If your current door rattles in a north wind off the 183 corridor, that’s the conversation to have before spring hail season, not after. Call (844) 560-4467 for a free on-site estimate.
How a Door Install Moves From Demo to Final Seal

Every door we install follows the same five stages. Here’s what happens on each, so you know what to expect when the crew pulls up.
Day 1 morning: measurement and tear-out
We pull the old door and frame, then check the rough opening for square, plumb, and rot. On older south Irving slab homes, this is where we find the surprises: soft sill plates, water intrusion behind the threshold, sometimes a header that’s been carrying load with no support. Tear-out takes two to four hours on a standard entry. You’ll decide then whether we replace the threshold and sill or reuse them, and that choice alone can swing the price $150 to $400.
Day 1 midday: framing and flashing
If the rough opening needs adjustment, we reframe it to spec. Then we flash the sill, jambs, and head – the layer most cheap installs skip and the one that keeps Irving’s driving spring rain out of your wall cavity. Flashing and framing run three to five hours. This is the stage where a wind-rated install earns its keep: proper anchor patterns and continuous weather barrier are what the inspection looks at, and what keeps the door from racking when a 60 mph gust hits.
Day 1 afternoon or Day 2: setting the door
We set the unit, shim it, and check that it swings and latches clean. On impact-rated doors this takes longer because the frame is heavier and the hardware tolerance is tighter. Expect four to six hours. You’ll confirm the swing direction, handle side, and finish before we lock it in.
Day 2 or 3: trim, seal, and finish
Interior and exterior trim, caulk, and paint-ready prep take a half day. We don’t paint; that’s yours or your painter’s call. We do seal every penetration so the door meets the wind and water rating it was sold with.
Final: inspection
If the job pulled a permit (more on that below), the city inspects framing and flashing before the job is signed off. We schedule that walkthrough and stay until it passes. Most jobs are complete inside three working days.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Door Installation isn’t one decision; it’s five. Here’s what the choices actually mean for an Irving home.
- Steel entry doors. The workhorse for wind-load areas. Heavy, stable, and rated systems are available. They dent under impact but hold structure. Best value for a front door facing an open lot.
- Fiberglass. Won’t rust or warp, holds paint, takes a wood-grain finish. Slightly lighter than steel, and it’s the strongest choice for a door with sun exposure on a west-facing wall.
- Wood. The premium look, and the one that needs the most upkeep in Irving’s heat. Beautiful on a covered porch; a maintenance commitment on an exposed elevation.
- Impact-rated glazing. If your door has glass, the glazing is what matters in a hail event. Impact glass costs more up front and takes storm damage off the table.
- Hardware and threshold. A commercial-grade threshold and multipoint lock add $200 to $600 and are the difference between a door that stays sealed for 15 years and one that leaks in year four.
What Door Installation Costs in Irving, TX

A single exterior door installation in Irving runs $450 to $2,400 installed, depending on what you pick and what’s behind the wall. Interior doors sit lower, $250 to $700 each. Here’s the line-item view.
| Item | Typical range |
|---|---|
| Standard pre-hung exterior door, installed | $450 – $1,100 |
| Impact or wind-rated entry system, installed | $1,200 – $2,400 |
| Interior door, installed | $250 – $700 |
| New opening cut in brick veneer | add $600 – $1,500 |
| Framing or header repair | add $300 – $900 |
| Permit and inspection | add $150 – $400 |
Four variables push a job to the high end: existing wall condition (rot, soft framing), whether we’re cutting a new opening or replacing in place, the material grade of the door itself, and whether the wall needs reinforcement for a wind rating. A written estimate spells out each of these. What we quote is what you pay; there are no change orders unless you ask for one.
If the door is part of a bigger envelope project, the wider scope lives on our Windows & Doors in Irving page, and you can see the full lineup on our Windows & Doors service hub.
See the difference
Before
After
Before
After
Before
AfterWhat Irving Homes Specifically Do to This Job
Irving is unusual: it has two construction worlds inside it, and each one fails doors differently. Along the 183 corridor in the older ZIPs (75060, 75061, 75062), you’re in 1950s-60s brick-veneer tract homes on slab. Those doors are original or one generation old, and the black-clay soil movement has racked plenty of frames out of square. We find sticking sills, gaps at the head, and rot behind thresholds constantly. In Valley Ranch and Las Colinas (75038, 75063), the issue is storm damage and HOA design review: replacement doors have to match the community’s approved profile, and hail-rated glazing is often the deciding spec.
Permits are the other split. A straight replace-in-place in an older home usually doesn’t require one, but a new opening or a structural header does, and the City of Irving inspects framing and flashing. HOA communities in Las Colinas and Valley Ranch add their own submission and approval step that can add a week to the schedule. We handle both: permits pulled and inspections passed, on our side.
Homeowners often pair a door install with Cabinets & Countertops in Irving when the same visit is covering an interior refresh, or with a Garage Conversion ADU in Irving when a new entry point is part of the plan. We cover the whole city, including the four ZIPs above, on our Irving service-area page.
Serving Irving, TX – Our Local Coverage Area
We serve Irving and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Door Installation in Irving

A standard exterior door replacement takes one day; a new opening cut into brick veneer takes two to three days including inspection. Interior doors are often done in half a day. If your HOA needs to approve the style first, add a week for that step. Call (844) 560-4467 to get a firm timeline for your home.
Replacing a door in its existing opening typically doesn’t need a permit; cutting a new opening or altering a structural header does. The City of Irving inspects framing and flashing on permitted work. We pull the permit and stay through the inspection. Call (844) 560-4467 and we’ll tell you which category your job falls into.
Plan on $450 to $2,400 for a single exterior door, installed, with impact-rated entry systems at the top of that band. Interior doors run $250 to $700 each. Call (844) 560-4467 for an exact quote – estimates are free and written line by line.
A properly rated and anchored door will; a cheap install won’t. Proper flashing, wind-load-rated anchoring, and impact glazing are what keep a door sealed and standing when hail and 60 mph gusts hit. We spec to those requirements and document the install. Call (844) 560-4467 to schedule an assessment.
Every door we install carries our 730-Day Done Right Promise – if it’s not done right, we make it right. That’s on top of the manufacturer’s warranty on the door itself. Call (844) 560-4467 if you have questions about coverage.
Get a Free Door Installation Estimate in Irving
If a door is rattling, sticking, or leaking, the fix is a same-week call, not a someday project. Call (844) 560-4467 and a live person answers, day or night. We’ll schedule a free on-site estimate, measure your opening, walk you through the material and rating options, and hand you a written quote with the price locked in. No surprises, no change orders. From foundation to finish line – and built to last, backed in writing.
Written by the team at Groundwork Construction Co.












