







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Door Installation in Frisco, TX: What It Involves and What It Costs
Door installation in Frisco typically runs $450 to $1,600 per interior door and $1,800 to $4,500 for a quality exterior entry door, with most homes needing three to six doors replaced at once. The job itself takes one to three days depending on how many doors and whether any framing needs correcting. Call (844) 560-4467 for a free on-site estimate with a written line-item quote.
How Our Door Installation Process Actually Runs

Door installation isn’t complicated, but it is sequential. Skip a step and you get a door that sticks, drafts, or won’t latch by the following spring. Here’s the real sequence.
Stage 1: Measure and Confirm (Day 1, 1-2 hours)
We measure every rough opening, check the plumb and square of each existing frame, and confirm the door style, swing direction, and hardware you want. This is where you make the decision that matters most: whether to keep your existing frame and trim or replace both. Keeping the frame saves money and time. Replacing it gives you a cleaner result if the original is out of square, which we find often in Frisco’s 1990s subdivisions.
Stage 2: Demo and Prep (Day 1, 2-4 hours per door)
Old doors come out, and we inspect what’s underneath. Rotted jamb bottoms, missing flashing, or an out-of-square opening all show up here. We repair the framing before anything new goes in. If we find water damage behind an exterior door, that’s the moment to address it, not after the new door is hung.
Stage 3: Hang and Shim (Day 2, 1-2 hours per door)
New doors go in level and plumb, shimmed at the hinge side and locked in with nails or screws through the jamb. We check the reveal gap around all four sides. This is where cheap installs fail: a door hung 1/8 inch out of square will drag within a year.
Stage 4: Hardware and Trim (Day 2-3, 1-2 hours per door)
Hinges, handles, locksets, and weatherstripping go on. Casing and trim get installed and caulked. You pick the finish here. This is also when we confirm the door swings the way you want and clears any furniture or flooring.
Stage 5: Final Check and Walkthrough (Day 3, 30-60 minutes)
We open and close every door through a full cycle, check for daylights around the edges, and confirm the locks engage cleanly. You walk through with us before we leave. Anything that needs adjustment gets adjusted on the spot.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Door choices come down to material, construction, and hardware. Here’s the honest trade-off on each.
- Solid wood vs. hollow core: Solid wood is heavier, quieter, and holds up better over time; expect to pay $250-$600 more per door. Hollow core is lighter and cheaper at $150-$400 but dents and swells more easily in North Texas humidity swings. Solid wood suits bedrooms and master suites; hollow core works fine for closets and utility rooms.
- MDF vs. solid core: MDF is smooth and paints cleanly, but it doesn’t handle moisture. Solid core holds up better near bathrooms and exterior entries. The price difference is $100-$200 per door.
- Exterior: fiberglass vs. steel vs. wood: Fiberglass resists denting and holds finish longer, running $1,200-$3,500 installed. Steel is cheaper at $800-$2,000 but dents and rusts if the paint fails. Wood looks best and costs most ($2,000-$5,000) but needs refinishing every few years in our climate.
- Hardware finish and grade: A standard builder-grade knob runs $25-$75. Upgrading to a smart lock or higher-grade mechanical set adds $150-$500. Kohler and Moen hardware we carry in the showroom range adds durability where builder-grade parts wear out first.
- Interior door style: Flat slab doors are the cheapest. Two-panel and five-panel raised styles add $50-$150 per door. Shaker-style panel doors are the most-requested in Frisco’s newer subdivisions and run mid-range.
What Door Installation Costs in Frisco, TX

Most Frisco door installation jobs land between $450 and $4,500 depending on door count and type. Here’s the breakdown.
| Item | Typical Frisco Range |
|---|---|
| Interior door (per door, installed) | $450 – $1,600 |
| Exterior entry door (installed) | $1,800 – $4,500 |
| Hardware and lockset | $25 – $500 |
| Trim and casing | $80 – $250 per door |
| Frame repair if out of square | $200 – $800 |
| Painting and finish | $75 – $200 per door |
What pushes a job to the high end: solid wood construction, exterior doors, frame replacement, smart-lock hardware, and any structural repair behind the opening. What keeps it low: hollow-core interior doors, keeping existing frames, and buying in volume (five or more doors at once).
Your written estimate covers doors, hardware, trim, installation labor, and cleanup. What’s usually excluded: painting (we can add it), structural framing repair if we find dry rot, and any custom sizes that need a lead time of four to six weeks. The number on the estimate is the number you pay. No change-order surprises.
See the difference
Before
After
Before
After
Before
AfterWhat Frisco Homes Specifically Do to Door Installation
Frisco was essentially built out in three decades. Nearly all single-family homes here date from the 1990s forward, and that means we’re almost never fixing old-house problems. We’re upgrading builder-grade doors that were never meant to last more than fifteen or twenty years. In ZIPs 75033, 75034, and 75035, whole subdivisions hit the same milestone at once, so entire streets of homes built within a few years of each other need the same door replacements in the same stretch. Walk a Frisco subdivision near The Star or along the Dallas North Tollway corridor and you’ll see it: identical 20-30 year old doors failing at the same rate.
The other Frisco-specific factor is blackland clay soil. Slab foundations here shift with wet-dry cycles, and when they do, door openings go out of square. We check frame plumb on every job, and we find sticking or dragging doors more often in Frisco than in cities with more stable soils. Hail and high wind events also take a toll on exterior doors and hardware, which is why fiberglass and steel entry doors hold up better here than wood. HOA rules in master-planned communities may specify door colors and styles, so check with your association before we order.
We cover all of Frisco and the surrounding towns, including Prosper, The Colony, and Little Elm. See our Frisco service area page for the full picture. If your project is part of a full Windows & Doors in Frisco scope, or you need a broader Windows & Doors plan, we coordinate the whole job on one schedule. Homeowners often pair this with Cabinets & Countertops in Frisco when a kitchen refresh is already underway, or with a Garage Conversion ADU in Frisco when an entry door is going into new construction.
Serving Frisco, TX – Our Local Coverage Area
We serve Frisco and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Door Installation in Frisco

A single interior door takes one to two hours. A full set of five to eight doors takes three to four days including demo, installation, trim, and final check. Exterior doors take longer, typically a full day each. Call (844) 560-4467 for a timeline estimate on your specific project.
Replacing a door in an existing opening generally does not require a permit. If you’re enlarging an opening, adding a new opening in a load-bearing wall, or converting a garage door to a solid door as part of an ADU, a permit and inspection are typically required. We handle the permit application and scheduling if your scope calls for it. Call us to confirm what your project needs.
Minor touch-up around the casing is normal, and a proper install minimizes it. We lay protection over floors and repair any drywall nicks before we leave. If a door needs an opening widened, that’s a bigger job and we discuss the scope before any cutting.
A standard fiberglass or steel entry door runs $1,800-$3,500 installed in Frisco. Wood entry doors run $2,000-$5,000. Adding sidelights, transoms, or a smart lock raises the total. Call (844) 560-4467 for an exact quote. Estimates are free.
Every door-installation job we do is covered by our 730-Day Done Right Promise. If a door we installed sticks, drafts, or fails within two years, we come back and make it right. The door itself may also carry a manufacturer’s warranty, which we explain in writing at the estimate.
Get a Free Door Installation Estimate in Frisco
Whether you’re replacing a single sticking door or the whole interior set in a Frisco home, we’ll come out, measure, and hand you a written estimate with itemized pricing. No guessing, no pressure. Call (844) 560-4467 and we’ll answer on the first ring. On the call we’ll ask about door count, interior or exterior, and the age of your home; from there we schedule a time to measure and give you a firm number. Estimates and design consults are free.
Written by the team at Groundwork Construction Co.












